Park Tool pin spanners and three newsworthy repairs you can do with them


One of my favorite bicycle wrenches are Park Tool pin/peg spanners. It’s because they are handy, strong, cheap and simple tools but also because of the different coloured grips that break the monotony of any tool wall display.

006

Spanners are made of hardened carbon steel to ensure long life while the handle is vinyl coated

My own experience tells me they are not on a daily basis tools anymore, but still esential for any all-round workshop that services freewheels or old fashioned bottom brackets for example.

The green handled SPA-1 fits the adjusting cup on many old three pieces cranksets. The pin ends are round with a diameter of 2.9mm.

The most popular repair you can tackle is a cup and cone type bottom bracket service.

Mural Park Tool SPA-1

Wherever there are two holes with the right size the Park Tool hanger cup pin spanner will allow you to do different repairs. Adjust the tension of the chain by turning the eccentric BB, removing a dustcup and so on

On the other hand, the SPA-2 red spanner has 2.3mm pin diameter. Due to its smaller size fits better a wider range of hole widths. It releases retaining rings on Shimano and Campagnolo crank bolts and the adjusting cone on most freewheel clusters.

A very interesting repair suitable with this tool is the removal of certain type of non-serviceable freewheels that don´t have an extraction tool option. A freewheel destructive removal method will require this spanner to get rid of the lockring.

The Park Tool cluster cone pin spanner is ideal for several repairs where a lockring needs to be removed, on self extracting or one-key release crank bolt systems or even if you need to fit/extract the guides of the BB facing tool inside the frame

The Park Tool cluster cone pin spanner is ideal for several repairs where a lockring needs to be removed, on self extracting or one-key release crank bolt systems or even if you need to fit/extract the guides of the BB facing tool inside the frame

The third and last peg spanner I own is the discontinued yellow SPA-4. It has a flat section designed to uncrew the adjusting cone of one-piece cranks. This is virtually the only repair you can do with this tool, the service of entry level cranksets on BMX’s and department store bikes.

The tool engages two notches of the adjustable left bearing cone. Rare cup and lockring cartridges BB's can also be serviced with the yellow spanner. The cup is run up to the bearings and then the lockring is secured. Note there is no bearing adjustment in this system

The tool engages two notches of the adjustable left bearing cone (2nd pic). Rare cup and lockring cartridges BB’s can also be serviced with the yellow spanner (3rd pic). The cup is run up to the bearings and then the lockring is secured. Note there is no bearing adjustment in this system. Nowadays the best use I found for it was while wrapping the handlebar of a road bike (4th pic)

At this point you might wonder what happens with the Park Tool reference SPA-3. Does it exist? Well, it does. But I haven´t seen one so far. It took me a lot of time to find a presentable picture of this tool and some information.

Blue and black peg spanners are top-rarity Park tools. SPA-3 has the ends facing one to each other. I don´t know the intended use for both tools. It seems the blue one can be used for adjusting old french bicycles headsets and the black for extracting crank bolts dust cups/retaining rings

Blue and black spanners are top-rarity Park tools. SPA-3 has the ends facing one to each other. I don´t know the intended use for both tools. It seems the blue one can be used for adjusting old french bicycles headsets and the black for extracting crank bolts dust cups/retaining rings

Meanwhile SPA-6 uses replaceable pins of approximately 2.2mm in diameter. The distance between the pins is adjustable, allowing use on virtually all hanger cups using pin holes. I have to say I do prefer fixed pegs as they are faster and more comfortable to use.

I have never faced a situation where you need to use the pin spanner wrench with such a distance between pins on a bicycle as in picture 2. Pin holes are likely to be close one to each other and thus more convenient a regular pin/peg spanner

I have never faced a situation where you need to use the pin spanner wrench with such a distance between pins on a bicycle as in picture 2. Pin holes are likely to be close one to each other and thus more convenient a regular pin/peg spanner

5 responses to “Park Tool pin spanners and three newsworthy repairs you can do with them

  1. Hola Fernando.

    Got useful info about the uses of the the Park tool SP tools.

    If you can provide an email address can send you a pic (official Park tool stuff) so you can complete your article, which is great by the way.

    Cheers.

    Alex.

  2. Article did a great job of explaining the uses of the different pin spanners- thank you, just what I was looking for!

  3. I have a brand new Park Tool SPA-3 in the original packaging. Make me a sensible offer if interested. Paul.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s